Search:

Type: Posts; User: cjurczak

Search: Search took 0.00 seconds.

  1. Replies
    24
    Views
    1,606

    I built quick connect slats for a display company...

    I built quick connect slats for a display company back in 2014, bent pins is not the biggest issue. They lose more than they break, to be honest I ran over a few in my truck after a shoot.

    The...
  2. Replies
    24
    Views
    1,606

    Have you seen the QuickSplit boards, I've heard...

    Have you seen the QuickSplit boards, I've heard they work great with the 18Ms
  3. Replies
    24
    Views
    1,606

    My perspective was mostly from the startup of a...

    My perspective was mostly from the startup of a display company point of view. I have been using quick connect/plug ematches since about ~2015. We were able to get more cues for our dollar by...
  4. Replies
    5
    Views
    227

    Without getting into to many details, you should...

    Without getting into to many details, you should be able to run minimum of 200ft of 23ga UTP cable with one ematch at the end without a problem. Cable is about 4 ohms/100ft, ematch is about 2 ohms,...
  5. Thread: Mongoose 2021

    by cjurczak
    Replies
    0
    Views
    285

    Mongoose 2021

    Anyone else use Mongoose over the 4th this year? I did 4 displays on a single charge, only one module dropped into the yellow, but was still managed to fire everything.

    I noticed one unit had a...
  6. Replies
    10
    Views
    1,807

    That?s correct, if you have 3 slats in parallel...

    That?s correct, if you have 3 slats in parallel if you have an ematch on any of the 3 you will see continuity. You will not be able to tell if you have 1, 2, or 3 ematches connected. It?s either go...
  7. If we order black Friday when can we expect to...

    If we order black Friday when can we expect to have it in our hands. Place orders on the website?
  8. If it doesn't have a ematch then you use a...

    If it doesn't have a ematch then you use a jumper. All positions need either a jumper or ematch to complete the circuit.
  9. Simplifire Mongoose also has a DMX control...

    Simplifire Mongoose also has a DMX control option. You could run one PC for xlights, music playback and Mongoose to keep everything in sync.
  10. Typical MJG resistance is ~2 ohms in series...

    Typical MJG resistance is ~2 ohms in series that's 24 ohms plus 300+300ft of 24 gauge wire adds another ~16 ohms. So for a ~30 ohm load and minimum all fire current of 600mA you need 18V firing...
  11. Replies
    2
    Views
    344

    Thanks Scott, fireTEK users haven't had an option...

    Thanks Scott, fireTEK users haven't had an option for quick connects until recently.
  12. We shot slices that were very similar, and had...

    We shot slices that were very similar, and had them 100' apart and 3 wide. Replay of the video showed they went about 220', and that's if they function as intended. Unlit comet/effect will fly...
  13. Replies
    2
    Views
    344

    Custom Firing System Slats from muuxBRD

    Special thanks to Dave for allowing me to post about muuxBRD. My name is C. J. and I have crossed my day job and passion for pyro to design and build custom firing system accessories. Until this...
  14. Replies
    4
    Views
    1,890

    I'm also from Illinois, have you decided to move...

    I'm also from Illinois, have you decided to move forward with your 54? Where are you in Illinois, I hope you aren't to discouraged with Illinois over-regulation. Get your 54, and partner up with a...
Results 1 to 14 of 14
-